FREEPHONE 0808 202 7303
Telephone: +44 (0)1208 264999
Fax: +44 (0)1208 264998
Email: info@reactiveresins.com
Telephone: +44 (0)1208 264999
Fax: +44 (0)1208 264998
Email: info@reactiveresins.com
BUY NOW
CALL FREE
0808 202 7303
CALL FREE
0808 202 7303
Links
CONSEAL P is a unique two-pack, low solvent epoxy primer sealer that can be applied to concrete immediately after it has been laid. CONSEAL P has a unique formulation that gives it the ability to mix with fresh wet concrete while still being resistant to diffusion of water through the uncured coating.
CONSEAL P will penetrate and seal moisture into the concrete so that it is available to react with the cement causing it to fully cure, even outdoors in extremely hot, dry conditions.
When CONSEAL P and the cement in the concrete substrate cure, they chemically react together ensuring that the CONSEAL P is permanently bonded to the concrete. The cured surface is far harder and more durable than concrete treated with conventional coatings in the usual way. CONSEAL P also eliminates all floor preparation work and enables rapid job completion.
CONSEAL P can be applied to reinforced concrete as soon as the form-work has been removed. CONSEAL P can also be applied to old concrete that has been suitably prepared.
CONSEAL P can be over-coated as soon as it is touch dry, usually between 6 and 12 hours, depending on the ambient temperature. Faster curing hardener is available for use in cold conditions or when rapid completion is required.
CONSEAL P can be applied to good quality concrete made to BS and ISO standards. It should not be applied to poor quality concrete that has been made with a large excess of water that will be trapped under the cured coating.
The table below shows that one coat of CONSEAL P will reduce the water loss of a cement moulding by at least 94%.
CONSEAL P will penetrate and seal moisture into the concrete so that it is available to react with the cement causing it to fully cure, even outdoors in extremely hot, dry conditions.
When CONSEAL P and the cement in the concrete substrate cure, they chemically react together ensuring that the CONSEAL P is permanently bonded to the concrete. The cured surface is far harder and more durable than concrete treated with conventional coatings in the usual way. CONSEAL P also eliminates all floor preparation work and enables rapid job completion.
CONSEAL P can be applied to reinforced concrete as soon as the form-work has been removed. CONSEAL P can also be applied to old concrete that has been suitably prepared.
CONSEAL P can be over-coated as soon as it is touch dry, usually between 6 and 12 hours, depending on the ambient temperature. Faster curing hardener is available for use in cold conditions or when rapid completion is required.
CONSEAL P can be applied to good quality concrete made to BS and ISO standards. It should not be applied to poor quality concrete that has been made with a large excess of water that will be trapped under the cured coating.
The table below shows that one coat of CONSEAL P will reduce the water loss of a cement moulding by at least 94%.
EPOXY PRIMER FOR NEW UN-CURED WET CONCRETE
Saves time & money when laying & finishing new concrete floors.
- Saves money by eliminating all preparation of new concrete floors.
- Promotes full cure of the concrete by eliminating water loss.
- Reacts with uncured concrete and permanently bonds to it.
- Quick cure allows fast over-coating and finishing of floors.
- Prevents dusting of the concrete surface caused by drying out.
Water loss of 3 : 1 Portland cement sample cast in metal tray 25 mm deep at 50oC.
Samples cured for 90 minutes at before coating. Water loss in mg/cm2
Samples cured for 90 minutes at before coating. Water loss in mg/cm2
1 Hour
2 Hours
4 Hours
8 Hours
24 Hours
7 Days
Uncoated
60
200
267
300
340
420
1 coat CONSEAL P
3.23
3.5
4.2
6.1
9.15
14.2
